Goulds Pumps 3700i API610 Installation, Operation And Maintenance Manual Download Page 53

Page: 53 / 126

5.4.1.3 Install the Radial Heat Flinger (As required)

Figure 28: Install the Air Cooling Package - Radial heat flinger

Remove the standard INPRO seal bearing isolator (123) and replace with INPRO radial heat flinger
(123B). Refer to

6.6.1 Assemble the power end on page 92

5.4.2 Bearing lubrication

Precautions

WARNING:

Risk of explosive hazard and premature failure from sparks and heat generation.

Ensure bearings are properly lubricated prior to startup.

Pumps are shipped without oil

You must lubricate oil-lubricated bearings at the job site.

Ring oil lubrication

Ring oil-lubricated bearings are standard. Bearing housings are supplied with constant-level oilers and
sight glasses. Make sure that oil ring properly seated in the grooves in the shaft.

5.4 Couple the pump and driver

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

Summary of Contents for 3700i API610































































































































Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands

Goulds Pumps 3700i API610, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands