Goulds Pumps 3700i API610 Installation, Operation And Maintenance Manual Download Page 50

Page: 50 / 126

Place one washer (534A) over the bolt (569E) and insert the bolt through the round hole at the front
end of the guard half.

Place a second washer (534B) over the exposed end of the bolt.

Thread a nut (570E) onto the exposed end of the bolt and tighten firmly.

570E

534B

534A

569E

Figure 23: Coupling guard hardware installation

Slightly spread the opening of the remaining coupling guard half (501B) and place it over the instal-
led coupling guard half so that the annular groove in the remaining coupling guard half faces the
driver.

501B

234A

Figure 24: Coupling guard motor

Place the end plate (234B) over the driver shaft and locate the end plate (234B) in the annular
groove at the rear of the coupling guard half (501B).

5.4 Couple the pump and driver

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

Summary of Contents for 3700i API610































































































































Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands

Goulds Pumps 3700i API610, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands