Goulds Pumps 3700i API610 Installation, Operation And Maintenance Manual Download Page 56

Page: 56 / 126

d) Place your thumb over the reservoir spout. Invert and insert the spout into the internal threaded

boss on the main body.

e) Tighten reservoir. Do not over-tighten.

Verify that proper oil level is maintained per the following diagram.

NOTICE:

Do not fill the oil reservoir of the bearing frame through the plug at the top.

Check that the oil level is correct. The correct oil level is centered in the bulls-eye sight glass, when
the pump is not in operation. During operation, bulls-eye sight gives a false oil level reading. Shown
is general schematic.

Figure 30: Checking oil level

5.4 Couple the pump and driver

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

Summary of Contents for 3700i API610































































































































Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands

Goulds Pumps 3700i API610, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands