Goulds Pumps 3700i API610 Installation, Operation And Maintenance Manual Download Page 107

Page: 107 / 126

122

184

Figure 75: Seal-chamber lock (register) runout

6.6.4 Install the cartridge-type mechanical seal and seal-chamber cover

NOTICE:

Refer to the mechanical seal manufacturer’s drawings and instructions for assistance during
the installation of the mechanical seal.

Remove the impeller.

a) Loosen and remove the impeller nut.
The impeller nut has left-hand threads.

b) Remove the impeller, impeller key, and seal-chamber cover (184) as described in the Disas-

sembly section.

Lubricate all O-rings with suitable lubricant, unless the seal manufacturer’s instructions indicate oth-
erwise.

Slide the cartridge seal assembly (rotary, stationary gland, gland gasket, and sleeve) onto the shaft
(122).

NOTICE:

Ensure that the mechanical-seal gland-piping connections are properly oriented.

6.6 Reassembly

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

105

Summary of Contents for 3700i API610































































































































Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands

Goulds Pumps 3700i API610, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands