Goulds Pumps 3700i API610 Installation, Operation And Maintenance Manual Download Page 106

Page: 106 / 126

If the total indicator reading is greater than the values shown in this table, determine the cause and
correct it.

Table 12: Maximum Allowable Seal Chamber Face Runout

Group

Maximum Allowable Total Indicator Reading

13i, 14i, 24i, 25i, 35i

0.05 mm | 0.002 in.

36i

0.065 mm | 0.0026 in.

47i

0.07 mm | 0.0028 in.

58i

0.08 mm | 0.0031 in.

122

184

Figure 74: Seal-chamber face runout

Check the seal-chamber lock (register) runout:

a) Mount a dial indicator on the shaft or shaft sleeve.

b) Rotate the shaft so that the indicator rides along the seal-chamber lock (register) for 360°.
If the total indicator reading is greater than 0.125 mm | 0.005 in., determine the cause and correct it.

6.6 Reassembly

104

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

Summary of Contents for 3700i API610































































































































Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands

Goulds Pumps 3700i API610, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands