Goulds Pumps 3700i API610 Installation, Operation And Maintenance Manual Download Page 62

Page: 62 / 126

Item Description

Discharge isolation valve

Check valve

Suction isolation valve

Figure 37: Suction supply above pump

5.7.2 Prime the pump with the suction supply below the pump

Use a foot valve and an outside source of liquid in order to prime the pump. The liquid can come from
one of these sources:

•

A priming pump

•

A pressurized discharge line

•

Another outside supply

Close the discharge isolation valve.

Open the air vent valves in the casing.

Open the valve in the outside supply line until only liquid escapes from the vent valves.

Close the vent valves.

Close the outside supply line.

5.7 Pump priming

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

Summary of Contents for 3700i API610































































































































Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands

Goulds Pumps 3700i API610, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands