Gorilla Treasure Trove II Assembly Manual Download

Page: 78 / 103

5/16 X 4-1/2"

5/16" WASHER

(OFFSET DOWN)

SANDBOX BOARD

2 X 6 X 36-3/4"

BOARD

TOP PANEL

HEX BOLT

2 X 4 X 36-3/4"

FRONT OF

TOWER

STEP 5: FRONT FRAME ASSEMBLY

5: DO NOT INSTALL LAG SCREWS AT THIS TIME.

1: PLACE THE 2 X 6 X 36-3/4" SANDBOX BOARD ON THE FRONT OF THE CORNER POSTS. THE HOLES IN THE

SANDBOX BOARD SHOULD BE OFFSET DOWN.

2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO THE

T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

3: PLACE THE 2 X 4 X 36-3/4" TOP PANEL BOARD ON THE FRONT OF THE CORNER POSTS.

4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE HOLES OF THE TOP PANEL BOARD TO

THE T-NUTS INSTALLED ON THE CORNER POSTS.

123

Summary of Contents for Treasure Trove II








































































































Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands

Gorilla Treasure Trove II, Assembly Manual

Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands