Gorilla Treasure Trove II Assembly Manual Download Page 3

Page: 3 / 103

FRONT POST

HEX BOLT

5/16" WASHER

2 X 6 X 78"

2 X 6 X 47-1/2"

TOP PANEL BOARD

2 X 6 X 47-1/2"

SIDE SANDBOX BOARD-LEFT

BOTTOM PANEL BOARD

4 X 4 X 96"

HEX BOLT

LEFT SIDE OF FORT

FRONT OF FORT

5/16" WASHER

(LEFT SIDE)

5/16" X 4-1/2"

5/16" WASHER

5/16" X 4-1/2"

HEX BOLT

5/16" X 4-1/2"

4 X 4 X 96"

MIDDLE

POST

(LEFT SIDE)

STEP 3: ASSEMBLING THE LEFT SIDE FRAME

1: LAY THE LEFT SIDE CORNER POSTS ON THE GROUND IN THEIR PROPER ORIENTATION.

2: LAY THE 2 X 6 X 78" SIDE SANDBOX BOARD - LEFT ON TOP OF THE LEFT SIDE CORNER POSTS AT THE BOTTOM

OF THE CORNER POSTS. THE HOLES IN THE SIDE SANDBOX BOARD - LEFT MUST BE OFFSET DOWN.

3: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SIDE SANDBOX BOARD

- LEFT TO THE T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

4: LAY THE 2 X 6 X 47-1/2" BOTTOM PANEL BOARD ON TOP OF THE LEFT SIDE CORNER POSTS IN THE MIDDLE OF

THE CORNER POSTS. THE HOLES IN THE BOTTOM PANEL BOARD MUST BE OFFSET DOWN.

5: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE BOTTOM HOLES OF THE BOTTOM PANEL

BOARD TO THE T-NUTS INSTALLED ON THE CORNER POSTS. THE TOP HOLES WILL BE USED LATER.

6: LAY THE 2 X 6 X 47-1/2" TOP PANEL BOARD ON TOP OF THE LEFT SIDE CORNER POSTS. THE HOLES IN THE TOP

PANEL BOARD MUST BE OFFSET DOWN.

7: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE TOP PANEL BOARD TO

THE T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

Summary of Contents for Treasure Trove II








































































































Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands

Gorilla Treasure Trove II, Assembly Manual

Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands