Gorilla Treasure Trove II Assembly Manual Download Page 64

Page: 64 / 103

1: TIE A KNOT AT ONE END OF THE 10' ROPE AND THREAD IT THROUGH THE BACK SIDE OF

THE HOLE IN THE ROPE LADDER SUPPORT.

2: THE UNTIED END WILL GO THROUGH THE HOLE OF THE BOTTOM ROCK WALL BOARD.

TIE A SECURE KNOT AT THE END MAKING SURE THAT THE ROPE IS TIGHT AND WILL NOT

WRAP AROUND YOUR HAND. HINT: TO REDUCE THE AMOUNT OF SLACK IN THE ROPE, LIFT

THE ROCK WALL ASSEMBLY SLIGHTLY WHEN TYING THE KNOT IN THE BOTTOM ROCK WALL

BOARD. WHEN YOU LOWER THE ASSEMBLY, THE KNOT WILL TIGHTEN.

STEP 64: ROCK WALL ROPE

TIE A KNOT AND THREAD

THE ROPE THROUGH THE

BACK SIDE OF THIS HOLE IN

THE ROPE LADDER SUPPORT

YOU MAY TIE UP TO THREE

KNOTS SPACED ABOUT 18"

APART TO AID IN CLIMBING.

109

Summary of Contents for Treasure Trove II








































































































Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands

Gorilla Treasure Trove II, Assembly Manual

Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands