Gorilla Treasure Trove II Assembly Manual Download Page 13

Page: 13 / 103

STEP 13: DECK BOARDS

A 1/8" DRILL BIT AT THE DIMENSIONS SHOWN BELOW.

1: PRE-DRILL THE ENDS OF THE DECK BOARDS TO PREVENT INSTALLATION DAMAGE. PRE-DRILL BOTH ENDS WITH

THE FOLLOWING STEP IS RECOMMENDED TO PREVENT POSSIBLE SPLITS IN THE WOOD

2: START WITH A 5/4 X 6 X 47-3/8" DECK BOARD AT ONE END OF THE FORT. CENTER THE BOARD BETWEEN THE

FRONT FACE BOARD AND THE REAR BOTTOM PANEL BOARD AND ATTACH IT WITH 2" WOOD SCREWS THROUGH

THE PREDRILED HOLES AND INTO THE DECK SUPPORTS BELOW. LEAVE A UNIFORM (APPROX. 1/4") SPACE

BETWEEN THE DECK BOARDS. NOTE: THE TOP OF THE SCREW HEAD SHOULD BE FLUSH TO THE TOP OF THE DECK

BOARDS.

LAY ALL DECK BOARDS ACROSS THE DECK SUPPORTS BEFORE SECURING THEM TO THE

FORT. THIS WILL ENSURE THAT YOU HAVE EQUAL SPACING ACROSS THE DECK.

5/4 X 6 X 47-3/8"

DECK BOARD

2" WOOD SCREW

4 "

23 11

8 "

1 3

4 "

2 3

1 3

8 "

5/4 X 6 X 47-3/8" DECK BOARD

Summary of Contents for Treasure Trove II








































































































Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands

Gorilla Treasure Trove II, Assembly Manual

Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands