Gorilla Treasure Trove II Assembly Manual Download

Page: 29 / 103

STEP 29: SLIDE BLOCK

1: PLACE THE 4 X 4 X 23-1/2" SLIDE BLOCK AGAINST THE UPPER DECK SUPPORT ON THE

LEFT SIDE (LADDER SIDE) OF THE PLAY SET. THE TOP OF THE BLOCK SHOULD BE FLUSH TO

THE TOP OF THE DECK SUPPORT. THE BLOCK FITS BETWEEN THE LAG POST AND THE REAR

CORNER POST.

2: HAVE AN ASSISTANT HOLD THE BOARD IN POSITION OR USE A CLAMP TO HOLD THE

BOARD FIRMLY TO THE DECK SUPPORT. USE THE HOLES IN THE SLIDE BLOCK AS A

TEMPLATE TO DRILL 3/8" HOLES THROUGH THE DECK SUPPORT.

3: HAMMER T-NUTS INTO THE HOLES ON THE INSIDE FACE OF THE DECK SUPPORT. ATTACH

THE SLIDE BLOCK TO THE DECK SUPPORT WITH 5/16" X 4-1/2" HEX BOLTS AND 5/16"

WASHERS.

DETAIL A

SCALE 2 : 25

4 X 4 X 23-1/2" SLIDE BLOCK

DECK SUPPORT

T-NUT

5/16"

WASHER

5/16" X 4-1/2"

HEX BOLT

Summary of Contents for Treasure Trove II








































































































Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands

Gorilla Treasure Trove II, Assembly Manual

Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands