manualshive.com logo in svg

Gorilla Treasure Trove II, Assembly Manual

Share
Download
Gorilla Treasure Trove II Assembly Manual Download Page 24

STEP 24: UPPER LEVEL - RAILING & UNDER DECK SUPPORT

1: PLACE THE 2 X 4 X 70" UPPER LEVEL STEPS/RAILING BOARD (3 HOLES ON CENTER) AT 

THE TOP OF THE REAR CORNER POSTS.  THIS BOARD WILL GET ATTACHED TO THE 2ND 

HOLE DOWN FROM THE TOP OF THE POSTS.  THE T-NUT FOR THIS BOARD SHOULD BE ON 

THE INSIDE OF EACH POST ALREADY.  FASTEN THE UPPER LEVEL RAILING BOARD TO THE 

REAR CORNER POSTS WITH 5/16" X 4-1/2" HEX BOLTS AND 5/16" WASHERS.

2: PLACE THE 2 X 6 X 70" SANDBOX BOARD (OFFSET UP) AT THE BOTTOM OF THE REAR 

CORNER POSTS.  FASTEN THE TOP HOLES IN THE SANDBOX BOARD TO THE REAR CORNER 

POSTS WITH 5/16" X 4-1/2" HEX BOLTS AND 5/16" WASHERS.

3: PLACE THE 4 X 4 X 70" UPPER LEVEL UNDER DECK SUPPORT DIRECTLY UNDERNEATH THE 

UPPER LEVEL DECK SUPPORTS.  ATTACH THE UNDER DECK SUPPORT TO THE REAR CORNER 

POSTS WITH 3/8" X 5" LAG SCREWS AND 3/8" WASHERS.

4-1/2"

HEX BOLT

HEX BOLT

5/16" WASHER

SANDBOX

4-1/2"

BOARD

UNDER DECK SUPPORT

UPPER LEVEL STEPS/RAILING BOARD

5/16" X 

(3 HOLES ON CENTER)

4 X 4 X 70" UPPER LEVEL

2 X 4 X 70" 

(OFFSET UP)

5/16" 

WASHER

2 X 6 X 70"

5/16" X 

3/8" 

WASHER

3/8" X 5"

LAG SCREW

69

Summary of Contents for Treasure Trove II








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands