Gorilla Treasure Trove II Assembly Manual Download

Page: 42 / 103

STEP 42: LOWER LEVEL FRONT CENTER TARP SUPPORT

1: LOCATE THE 4 X 4 X72" CENTER TARP SUPPORT. PLACE THE 4 X 4 X 72" CENTER TARP

SUPPORT CENTERED BEHIND THE HOLE IN THE ROPE LADDER SUPPORT.

2: HAMMER A T-NUT INTO THE HOLE IN THE BACK SIDE OF THE CENTER POST. FASTEN THE

CENTER TARP SUPPORT TO THE ROPE LADDER SUPPORT WITH A 5/16" X 4-1/2" HEX BOLT

AND A 5/16" WASHER.

3: SQUARE THE CENTER TARP SUPPORT TO THE DECK. ATTACH THE CENTER TARP SUPPORT

TO THE FRONT FACE BOARD WITH TWO #8 X 3" WOOD SCREWS FROM THE FRONT. GO

UNDER THE FORT DECK AND INSTALL THREE #8 X 3" WOOD SCREWS THROUGH THE

CENTER DECK BOARD INTO THE BOTTOM OF THE CENTER TARP SUPPORT.

4 X 4 X 72"

5/16" WASHER

T-NUT

#8 X 3" WOOD SCREW

SUPPORT

(3 UNDER DECK)

5/16" X 4-1/2"

CENTER TARP

SUPPORT

#8 X 3" WOOD SCREW

(2 AT FRONT)

HEX BOLT

ROPE

LADDER

FRONT FACE BOARD

Summary of Contents for Treasure Trove II








































































































Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands

Gorilla Treasure Trove II, Assembly Manual

Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands