background image

© Copyright 2011, DB Industries, Inc.

Safl ok

Steel Structure Fall Arrest System

Models

Certi

fi

cate No. FM 39709

I S O

9 0 0 1

2104810

ANSI Z359-1

2104811

CSA Z259.2.1

USER INSTRUCTION MANUAL:

SAFLOK™ STEEL STRUCTURE FALL ARREST SYSTEM

This manual is intended to meet the Manufacturer’s Instructions requirement of applicable standards defi ned in 

Section 1.2 and should be used as part of an employee training program as required by the identifi ed agencies.

Form: 5903151  Rev: A

WARNING: This product is part of a personal fall arrest system

1

. The user must read and follow the 

manufacturer’s instructions for each component or part of the complete system. These instructions must be 

provided to the user of this equipment. The user must read and understand these instructions or have them 

explained to them before using this equipment. Manufacturer’s instructions must be followed for proper use and 

maintenance of this product. Alterations or misuse of this product or failure to follow instructions may result in 

serious injury or death.

1

IMPORTANT: If you have questions on the use, care, or suitability of this equipment for your application, 

contact Capital Safety.

IMPORTANT: Record the product identifi cation information from the ID label in the Inspection and Maintenance 

Log in Section 9.

DESCRIPTION:

Figure 1 illustrates the components that comprise the Sa

fl

 ok

 Steel Structure Fall Arrest System. The 

Steel Structure Fall Arrest System consists of a dielectric Vertical Lifeline Rope (A) passing through a formed 

Anchor Tube (B). The Anchor Tube drapes over steel lattice or steel beam structures and is placed with a 

Telescoping Hot Stick (C) and attached Installation/Removal Tool (D) to suspend the lifeline vertically for 

attachment of a fall arrest subsystem: Rope Grab (E) with Shock Absorber (F), and Full Body Harness. A Web 

Strap (H) is provided to secure the bottom end of the lifeline to the base of the structure.

Figure 1 –  Safl ok™ Steel Structure Fall Arrest System

Item

Description

Qty.

A

Vertical Lifeline Rope

1

B

Anchor Tube

1

C

Telescoping Hot Stick

(purchased separately)

0

D

Installation/Removal Tool

1

E

F

Rope Grab with

Shock Absorber

1

1

G

Web Strap

1

H

Carabiner

1

I

Carrying Bag

1

2-Rope Grabs:

Model 2104810 comes with Fuji Rope Grab

Model 2104811 comes with Protecta Rope Grab

I

B

A

E

D

F

H

G

1  Fall Arrest System: A system that prevents the worker from colliding with an obstruction or lower level by arresting a fall.

Summary of Contents for Saflok 2104810

















Reviews: