Gorilla Treasure Trove II Assembly Manual Download

Page: 1 / 103

POSTS DO

LEFT SIDE OF FORT

MIDDLE

POST

4 X 4 X 96"

FRONT OF FORT

4 X 4 X 96"

CORNER

TO SEAL THE HOLES.

FRONT

MIDDLE

4 X 4 X 96"

CORNER

MIDDLE

OF SILICONE ON EACH PLUG

POSTS SHOULD BE FACING THIS DIRECTION.

THE FRONT

NOT HAVE.

THE FRONT

POSTS. USE A DAB

CARRIAGE BOLTS.)

THE TOP HOLES IN ALL THE CORNER

PLACE A PLASTIC PLUG INTO EACH OF

HERE THAT

EXTRA HOLE

CORNER

BEAM MOUNT USING

HOLES AT THE TOP OF THE CORNER

HAVE AN

NOT HAVE.

POSTS DO

POSTS

POST

NO T-NUT IN THESE

HOLES (FOR SWING

CORNER

POST

MIDDLE

CORNER

POSTS

HAVE AN

EXTRA HOLE

HERE THAT

RIGHT

SIDE OF

FORT

STEP 1: ATTACHING T-NUTS TO THE CORNER POSTS

1: THIS STEP IS CRITICAL TO BUILDING THE FORT PROPERLY. IF ANY MISTAKES ARE MADE HERE, YOU WILL NEED

TODIS-ASSEMBLE AND THEN RE-ASSEMBLE TO MAKE YOUR CORRECTIONS.

2: MAKE SURE HOLES ARE FREE OF ANY OBSTRUCTIONS. USE A BOLT TO CLEAN OUT ANY DEBRIS.

3: LAY OUT EACH OF THE 4 X 4 X 96" CORNER POSTS IN THE AREA YOU INTEND ON BUILDING THE FORT SIDE OF

THE PLAYSET.

4: USE THE DIAGRAM BELOW TO CORRECTLY IDENTIFY AND ORIENT THE NECESSARY DIRECTION THE POSTS

SHOULD FACE.

5: USE A HAMMER TO SEAT THE T-NUTS AFTER INSERTING THEM INTO THE HOLES SHOWN IN THE DIAGRAM BELOW.

6: THE BARREL OF THE T-NUT SHOULD GO IN THE HOLE FIRST. HAMMER THE T-NUT UNTIL IT IS FLUSH/ALMOST FLUSH

TO THE CORNER POSTS.

7: PLACE A PLASTIC PLUG INTO ALL THE CORNER POST TOP HOLES. USE A DAB OF SILICONE ON THE PLUGS

TO SEAL THE HOLES.

Summary of Contents for Treasure Trove II








































































































Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands

Gorilla Treasure Trove II, Assembly Manual

Search results

Summary of Contents for Treasure Trove II

Reviews:

Related manuals for Treasure Trove II

Brands by name

Popular brands