background image

 

 

 

ROLL.in.One Installation Instructions & O

wner’s 

Manual 

Page 12 

 

Owner’s Manual for the 

 

R

oll

.in.One Automatic Roller Door Operator 

 
 

CONGRATULATIONS! 

On the purchase of your Roll.in.One Automatic Roller Door Opener 

 

INDEX 

 

Page 

 

Page 

Door Operation  

13 

Key Ring Handset 

13 

Manual Operation 

13 

Wireless Wall Button Switch 

13 

Obstruction Detection 

13 

Photo Electric Sensor 

13 

Vacation Mode 

13 

Trouble shooting table 

14 

Automatic Closing 

13 

Technical Specifications 

15 

Courtesy Light 

13 

Warranty 

16-17 

Audible Buzzer 

13 

Warranty Form 

18 

Rolling Code Security 

13 

Sales & Service 

18 

 

Door Operation 

A roller door equipped with a Roll.in.One opener may be 
operated by using the handheld Transmitter. 

 

Momentary activation of the above method will activate 
the door to open or close. 

 

!  WARNING  -  Ensure  that  the  Centre  Lift  Lock  is  not 
engaged  when  the  Drive  Unit  is  in  the  automatic 
position. 

 

Manual Operation

 

In the case of a power failure the Roll.in.One opener has 
an  easily  accessible  manual  release  chord.  Pulling  the 
manual release chord once will set the door for manual 
operation  and  pulling  it  again  will  set  the  door  for 
electric operation.

  

Obstruction Detection 

During  an  open  cycle  if  an  obstruction  is  detected,  the 
door will stop. During a closing cycle if an obstruction is 
detected, the door will reverse to the open position. The 
sensitivity  or  the  amount  force  required  to  cause 
obstruction  detection  is  fully  adjustable  (refer  to  5.0 
Force setting on page-10) for force adjustment. 

 

Vacation Mode 

When  the  door  is  not  used  for  a  long  time  or  during 
vacation  it  can  be  set  to  vacation  mode  for  security 
purposes. To activate & deactivate vacation mode refer 
to 8.0 on page-10. 

Automatic Closing 

The  Roll.in.One  opener  can  be  programmed  to 
automatically close from 10 to 30 seconds after the door 
has  been  opened  (refer  to  6.0  on  page-10)  to  activate 
and deactivate Auto- Close function. 

Courtesy Light  

An  internal  courtesy  LED  light  is  housed  within  the 
control  box  enclosure.  This  is  activated  during  an  open 
or close cycle and will stay illuminated for approximately 
60 seconds. 
 

 

 
 

Audible Buzzer 

The Roll.in.One has an internal Piezo Siren that will beep 
momentarily  each  time  the  door  is  activated  by  factory 
default it will be enabled. 
This  function  can  be  disabled  if  required  to  disable 

remove  jumper  ‘j9’  next  to  buzzer  ‘Bz1’  refer  to  PCB 

index diagram on page-7. 

 

Rolling Code Security 

The transmitter and receiver incorporate the latest state 
of the art encryption technology. 
This allows the coded transmission to change after each 
operation with literally billions of unique combinations. 
Each Roll.in.One opener has the facility to store up to 15 
individual handsets. 

 

Key Ring Handset 

The  hand  transmitter  is  manufactured  using  the  latest 
surface mount technology and incorporates 3 functional 
buttons. This enables the user to remotely control up to 
3 separate operators from the one handset or configure 
each button to operate OPEN / CLOSE / STOP functions.  

Wireless wall Button Switch 

A  wireless  wall  button,  single  or  three  buttons  can  be 
mounted on the wall to operate the door. 

Photo-electric sensor 

The Roll.in.One roller door opener includes an interface 
for the connection of a photo-beam sensor. When fitted, 
during  door  closing  if  the  photo  sensor  has  been 
triggered  the  door  will  auto  reverse  with  continuous 
beep sound. The Photo-beam sensor can be supplied as 
an accessory option. 

(Refer to 10.0 on page 12 for wiring 

diagram) 

 

! WARNING - In some countries it is a legal requirement 
to  fit  Photo-cell  sensors.  Please  check  with  your  local 
distributor 

 

 

 

 

 

Summary of Contents for Roll.in.One
















Reviews: