Gliderol Roll.in.One Installation Instructions Manual Download

Page: 11 / 15

ROLL.in.One Installation Instructions & O

wner’s

Manual

Page 11

7.0 LED Control

Under 3 Keys transmitter mode, the LED can be switched on and off using the STOP key.

8.0 Vacation Mode

Transmitter signal can be locked out by pressing STOP & CLOSE keys simultaneously and holding it for 3 seconds
on the transmitter. To deactivate, press the same keys again and hold it for 3 seconds.

9.0 Key Ring Transmitter

Battery Type 3V CR2016x2 (Lithium Cell)

To replace batteries:
1.

Remove the screw on the back case.

Replace the old batteries with new ones (3V CR2016x2) and ensure plastic strip remain intact in clip.

Locate back of case and secure with screw.

10.0 Photo Sensor Connection Diagram

Plastic Strip

GND-Black

COM-Brown

N,O-White

12V-Red

N,C-Yellow

Summary of Contents for Roll.in.One
















Search results

Summary of Contents for Roll.in.One

Reviews:

Related manuals for Roll.in.One

Brands by name

Popular brands

Gliderol Roll.in.One, Installation Instructions Manual

Search results

Summary of Contents for Roll.in.One

Reviews:

Related manuals for Roll.in.One

Brands by name

Popular brands