Gliderol Roll.in.One Installation Instructions Manual Download

Page: 9 / 15

ROLL.in.One Installation Instructions & O

wner’s

Manual

Page 9

2 beeps will signal for successful coding and a transmitter already in memory

Unit will automatically exit the setup

Single Button Configuration:

Any one of the three buttons in the transmitter can be used to control all three

functions Stop/Open/Close. Useful when one transmitter can operate more than one door and a maximum
of three doors.

3.0 Transmitter Code Erase

Press and hold [C] for 8 seconds, [CODE] will light

While LED diminishes, ALL codes have been erased

4.0 Limit Setting

–

By Controller

Press and hold [ S] button, release finger while the red light turns from [F] to [L]

Press [S] again, when the light of [SEL/ADJ] turns RED or GREEN, select the desire drive handing

RED

indicates Left Hand Drive

GREEN

indicates Right Hand Drive

Release finger after selecting the right mode with 3 beeps after 4~5 seconds, and then light of [SEL/ADJ] turns
green and starts blinking

Proceed to setup the TOP limit, by pressing [OPEN] button on transmitter, and confirm TOP limit position by
pressing [STOP] button. 2 beeps will signal for successful programming.
**While setting the TOP limit the [SEL/ADJ] light will turn

green

and starts blink.

[KEY1]
Stop/Open/Close

[KEY1] STOP
[KEY2] OPEN
[KEY3] CLOSE

Three Button Configuration:

Each buttons in the transmitter can be used to control

individual functions like functions Stop/Open/Close of the same door.

Summary of Contents for Roll.in.One
















Search results

Summary of Contents for Roll.in.One

Reviews:

Related manuals for Roll.in.One

Brands by name

Popular brands

Gliderol Roll.in.One, Installation Instructions Manual

Search results

Summary of Contents for Roll.in.One

Reviews:

Related manuals for Roll.in.One

Brands by name

Popular brands