Glentek SMB9675-1A-1-6889 Installation & Operation Manual Download | Manualshive

Page: 6 / 24

background image

4

2.3. Communicating With The Vector Drive

2.3.1. Serial Port
If your PC has a serial port (RS-232) you can connect to the vector drive with Glentek
cable (GTK # GC2400-AL005AM-000). This cable has a female DB-9 (computer) on
one end and an RJ-45 (vector drive) on the other.

2.3.2. USB Port
If your PC has a USB port, a USB to serial port (RS-232) adapter (GTK # GC2410-
001). is necessary in addition to the cable above. Two known tested adapters are
available: USBG-232 from USBGEAR and US232R-10 from FUTURE TECHNOLOGY
DEVICES INTERNATIONAL Ltd.

GC2400-AL005AM-000

SERIAL PORT ON THE VECTOR DRIVE

USBG-232

«
...
4
5
6
7
8
...
»

Summary of Contents for SMB9675-1A-1-6889

























Reviews:

No comments

Related manuals for SMB9675-1A-1-6889

DFPI-xxx-ND2P-E-NB3 Series

Brand: Festo Pages: 4

Brand: D+H Pages: 12

Sonesse ULTRA 30 WireFree RTS Li-ion

Brand: SOMFY Pages: 2

SINAMICS S210 FSA

Brand: Siemens Pages: 2

MICROMASTER 6SE92

Brand: Siemens Pages: 2

SIMODRIVE POSMO SI

Brand: Siemens Pages: 2

Brand: Siemens Pages: 6

SIMATIC MICRO-DRIVE

Brand: Siemens Pages: 39

1FL3041-0AC31-0BJ0

Brand: Siemens Pages: 60

6SL3210-5CC14-0UA0

Brand: Siemens Pages: 68

Brand: Siemens Pages: 100

Brand: Siemens Pages: 112

Brand: Siemens Pages: 124

SIMOREG DC Master 6RA7018-6DS22

Brand: Siemens Pages: 616

Brand: Leadshine Technology Pages: 13

Brand: KB Electronics Pages: 18

Brand: LSIS Pages: 81

Brand: Iomega Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands