GX9000 User manual
Rev 2.1
Timecode
ode
Input Timecode Frequency
Input Timecode Frequency
The GX9000 can detect the rate of the incoming timecode by measuring the
distance between frame boundaries. You can use this measurement to check
the rate of the input timecode is as expected and also to automatically select
the internal generator rate.
The GX9000 can detect the rate of the incoming timecode by measuring the
distance between frame boundaries. You can use this measurement to check
the rate of the input timecode is as expected and also to automatically select
the internal generator rate.
•
Press
the
Setup
button.
•
Press
the
Setup
button.
•
Use
the
Rotary Wheel
and
Parameter Up
and
Parameter Down
buttons
to select the
Sync | .TC Freq
menu heading.
•
Use
the
Rotary Wheel
and
Parameter Up
and
Parameter Down
buttons
to select the
Sync | .TC Freq
menu heading.
The lower alpha numeric display will show the rate of the incoming timecode
in frames per second. To set the generator to automatically select this rate.
The lower alpha numeric display will show the rate of the incoming timecode
in frames per second. To set the generator to automatically select this rate.
•
Use
the
Rotary Wheel
to select the
Sync | .GenRate
menu
heading.
•
Use
the
Rotary Wheel
to select the
Sync | .GenRate
menu
heading.
Genex Audio Inc
Page 52
Genex Audio Inc
Page 52
•
Use
the
Value Up
and
Value Down
buttons to select either
Auto
or
Manual
. In
Manual
mode the user programs the generator rate as
described below. In
Auto
the generator rate is automatically set to value
measured by the internal frequency counter and shown in the
.TC
Freq
heading.
•
Use
the
Value Up
and
Value Down
buttons to select either
Auto
or
Manual
. In
Manual
mode the user programs the generator rate as
described below. In
Auto
the generator rate is automatically set to value
measured by the internal frequency counter and shown in the
.TC
Freq
heading.
•
Press
the
Enter
button to confirm the change.
•
Press
the
Enter
button to confirm the change.
3
Sync
T
3
.
GenRate
UV
Auto
Manual
Timecode Rate
Timecode Rate
This heading displays the rate and count sequence for the timecode
generator.
This heading displays the rate and count sequence for the timecode
generator.
3
Sync
T
3
.
TC Rate
UV
24F
25F
29DF
29NDF
30NDF
The
.TC Rate
heading will blink if the selected timecode rate does not
match the rate for a currently open project or recording.
The
.TC Rate
heading will blink if the selected timecode rate does not
match the rate for a currently open project or recording.
You can adjust the timecode rate to be different to the rate selected for the
originally recorded data. The unit will then ‘cross-code’ the two rates so that
all cue points and locate points remain correct.
You can adjust the timecode rate to be different to the rate selected for the
originally recorded data. The unit will then ‘cross-code’ the two rates so that
all cue points and locate points remain correct.
Dropping into record in an existing non blank project will restore the timecode
generator rate to match that of the existing project or recording.
Dropping into record in an existing non blank project will restore the timecode
generator rate to match that of the existing project or recording.
To change the rate,
To change the rate,
•
Press
the
Setup
button.
•
Press
the
Setup
button.
•
Use
the
Rotary Wheel
and
Parameter Up
and
Parameter Down
buttons
to select the
Sync | .Tc Rate
menu heading.
•
Use
the
Rotary Wheel
and
Parameter Up
and
Parameter Down
buttons
to select the
Sync | .Tc Rate
menu heading.
•
Press
the
Value Up
and
Value Down
buttons to select a new rate.
•
Press
the
Value Up
and
Value Down
buttons to select a new rate.
•
Press
the
Enter
button to confirm the change.
•
Press
the
Enter
button to confirm the change.
Stop Timecode
Stop Timecode
The GX9000 can generate still frame LTC when stopped. This can cause
problems with some older synchronisers which don’t expect a machine to be
able to read timecode at 0 speed.
The GX9000 can generate still frame LTC when stopped. This can cause
problems with some older synchronisers which don’t expect a machine to be
able to read timecode at 0 speed.
Use the
Off
setting to stop timecode signals being produced at the rear
panel LTC output connector when the unit is in stop.
Use the
Off
setting to stop timecode signals being produced at the rear
panel LTC output connector when the unit is in stop.
3
Sync
T
3
.
Stop TC
UV
Still Fr
Off