General Standards Corporation PCI-SIO4 User Manual Download Page 14

Page: 14 / 66

PCI-SIO4 User Manual

General Standards Corporation

8302A Whitesburg Drive Huntsville, AL 35802, Phone: (256) 880-8787

1.2

BOARD CONTROL REGISTER

The board control register will provide configuration for the PCI/DMA request priorities.

1.3

BOARD STATUS REGISTER

The board status register will provide status of the board (for future expansion).

1.4

SYNC WORD SELECTION REGISTERS

The sync word selection registers are used to provide an interrupt upon the reception of a particular

character on a particular channel. The character is software programmable.

1.5

DATA RECEPTION

Data is received into the Zilog Z16C30. After the data is received, the software may retrieve the data from

the Z16C30 or have the data buffered into the main Rx FIFOs and retrieved by the software at a later time,

depending on how the Z16C30 has been initialized.

1.6

DATA TRANSMISSION

Data is placed into the Zilog Z16C30 or buffered into the main Tx FIFOs, depending on how the Z16C30

has been initialized. The Zilog can transmit and receive in any of several serial protocols:

•

Asynchronous

•

External Sync

•

Isochronous

•

Asynchronous with Code Violations

•

Monosynchronous

•

Bisynchronous

•

HDLC

•

SDLC

•

Plus many more

1.7

ERROR DETECTION

By utilizing the features of the Z16C30, various forms of error detection are built into the board. The

following are some of the methods of error detection available:

•

Parity error detection

•

CRC error detection

•

Rx overrun

•

Tx underrun

1.8

INTERRUPTS

Interrupts will be provided for the following conditions:

•

DMA Complete

•

Sync word detected

Summary of Contents for PCI-SIO4



































































Search results

Summary of Contents for PCI-SIO4

Reviews:

Related manuals for PCI-SIO4

Brands by name

Popular brands

General Standards Corporation PCI-SIO4, User Manual

Search results

Summary of Contents for PCI-SIO4

Reviews:

Related manuals for PCI-SIO4

Brands by name

Popular brands