background image

Change

Hint:

z

When assembling, please work by the sequence which is opposite with disassembling

sequence; if necessary, it will have assembling instruction.

z

Please refer to subassembly figure of rear bumper on page 381.

Exterior/inner trim board--Rear bumper

 382 

1. Disassemble trunk carpet assembly [68000114]

2. Disassemble rear trim board of trunk [68000118]

(a) Use two fixing clasps.

(b) Use disassembling tool for trim tape to disassemble rear

trim board of trunk.

3. Disassemble left decoration of trunk [68000112]

(a) Use disassembling tool for fixing clamp to disassemble

fixing clamp and a part of left decoration of trunk.

Hint:

Disassemble the fixing clasp and left decoration of trunk in the scope of screw cap used for

fixing rear bumper and trunk which could be disassembled.

4. Disassemble right decoration of trunk [68000113]

5. Disassemble mudguard of left rear wheel [68000223]

(a) Disassemble two screws and mudguard of left rear wheel.

6. Disassemble mudguard of right rear wheel [68000224]

7. Disassemble trim board of left rear wheel [68000230]

(a) Use screw driver to disassemble fixing clasp from rear bumper.

(b) Use disassembling tool for fixing clasp to disassemble fix-

ing clasp.

(c) Disassemble trim board of left rear wheel.

Hint: Disassemble trim board of left rear wheel in the

scope of screw used for fixing rear bumper which could

be disassembled.

8. Disassemble trim board of right rear wheel [68000231]

9. Disassemble rear bumper [68000012]

(a) Use screw driver to disassemble two fixing clasps.

(b) Disassemble four screw caps and two screws.

(c) Disassemble fixing clasp and rear bumper.

(d) Equipping with radar probe head: disassemble four joints of

radar probe head.

10. Disassemble reversing radar probe head assembly.

(a) Disassemble fixing pedestal of radar probe and radar probe.

11. Disassemble left rear fog light assembly [67000100]

(a) Disassemble fixing nut and left rear fog light assembly.

12. Disassemble right rear fog light assembly  [67000101]

Summary of Contents for FC




































































































































































































































































































































































































































Reviews: