GE Voluson Swift Instructions For Use Manual Download Page 29 | Manualshive

Page: 29 / 344

background image

Contrast media

Caution

•

Cavitation may occur due to interactions between the ultrasonic waves and the contrast

medium. Always perform examination using the ALARA (As Low As Reasonably

Achievable) principle. The acoustic power can be adjusted by the Acoustic Output slider

on the user interface.

•

Stop the examination and perform appropriate treatment, if there is any abnormality with

the patient during use of the contrast medium.

In the United States contrast agent usage is restricted to usage on LVO (Left Ventricle

Outflow).

Remark

•

Contrast agent restrictions varies per country. Consult local guidelines for approved

used.

•

Handle the contrast medium as described in the operation Instructions for Use supplied

with the contrast medium.

•

Check the side effects of the contrast medium used with the manufacturer of the contrast

medium.

•

GE ULTRASOUND KOREA, LTD. is not liable for any damage or injury resulting from

improper use of contrast media.

Probe orientation

Caution
Ensure that the actual probe position corresponds to the probe orientation configuration.
Special accuracy is required in Acquisition Mode 4D. Moving the probe can lead to errors in

displayed directions with respect to the displayed image.

2.7 Cleaning the system

Warning

•

Before cleaning the console switch it off and disconnect from AC mains.

•

Electric parts must be protected from liquids.

Cleaning

Caution
The following table provides cleaning instructions for the ultrasound device. It is the

responsibility of the user to decide which cleaning procedure is necessary to ensure a safe

working environment.

•

Electrical contacts and connectors must not be cleaned.

•

Only use cleaning agents listed in the below table.

•

Do not use high-proof alcohol (over 70% ) for cleaning the system.

•

If you use a spray, apply it on a piece of cloth or tissue and then wipe the system. Do not

apply spray directly onto the system, to prevent liquids from entering.

Safety

Voluson™ SWIFT / Voluson SWIFT+ Instructions For Use
5831612-100 Revision 4

2-15

«
...
27
28
29
30
31
...
»

Summary of Contents for Voluson Swift

























































































































































































































































































































































Reviews:

No comments

Related manuals for Voluson Swift

Brand: Bacharach Pages: 48

Brand: CAMAG Pages: 40

Brand: Parker Pages: 39

Brand: Raytheon Pages: 68

Brand: KegLand Pages: 23

Brand: M-system Pages: 5

Brand: MA Pages: 2

Brand: Safety 1st Pages: 4

Brand: Safety Engineering Pages: 5

Brand: Garmin Pages: 2

Brand: Daekyung Pages: 15

Raven OMNiPOWER NL5000 G5

Brand: New Leader Pages: 268

Brand: Jandy Pages: 52

Brand: WalimeXPro Pages: 23

SEEDMATIC PROFESSIONAL 8124A

Brand: Aitchison Pages: 50

Brand: IEMCA Pages: 85

Brand: JB Systems Pages: 9

MXI VXI-PCI8026

Brand: National Instruments Pages: 132

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands