GE TMO2D User Manual Download

Page: 67 / 102

TMO2D Digital Display User’s Manual

Chapter 5. Advanced Programming

5.9 Manual Offset?

The

Manual Offset?

option enables you to apply a manually-entered offset (in percent or PPM) to the gas calculations.

5.10Change AutoCal Limits?

The

Change AutoCal Limits?

option enables you to adjust the error handling limits for auto calibration. (To program

basic auto cal parameters, refer to

Auto Cal Parameters

on page 42.) The TMO2D has default values for error

handling:

•

Total Calibration Drift Limit: 40% of input range (6.40 mA)

•

Drift per Calibration Limit: 25% of input range (4.00 mA)

•

Verification Mode Drift Limit: 10% of input range (1.6 mA)

FACTORY SETUP MENU
Manual Offset?

Press [YES] to apply a manual offset to the gas calculations.

FACTORY SETUP MENU
% Offset: [X.XX]:

Use the numeric keys to enter the desired value (in % or ppm). Press [YES] to enter
the value, and [YES] again to confirm the entry.

FACTORY SETUP MENU
Manual Offset?

Press [NO] to proceed to the Change AutoCal Limits? option.

FACTORY SETUP MENU
Change AutoCal Limits?

Press [YES] to change the error handling limits for auto calibration.

AUTOCAL DRIFT LIMITS
Edit Tot Drift Limit?

Press [YES] to edit the total calibration drift limit.

Set Total Cal Drift:
Drift mA [X.XX]:

Use the numeric keys to enter the desired limit. Press [YES] to enter the value, and
[YES] again to confirm the entry.

AUTOCAL DRIFT LIMITS
Edit Tot Drift Limit?

Press [NO] to proceed to the drift per calibration limit.

AUTOCAL DRIFT LIMITS
Edit per cal Limit?

Press [YES] to edit the drift per calibration limit.

Set Max Drift Per Cal:
Drift mA [X.XX]:

Use the numeric keys to enter the desired limit. Press [YES] to enter the value, and
[YES] again to confirm the entry.

AUTOCAL DRIFT LIMITS
Edit per cal Limit?

Press [NO] to proceed to the verification mode drift limit.

Summary of Contents for TMO2D







































































































Search results

Summary of Contents for TMO2D

Reviews:

Related manuals for TMO2D

Brands by name

Popular brands

GE TMO2D, User Manual

Search results

Summary of Contents for TMO2D

Reviews:

Related manuals for TMO2D

Brands by name

Popular brands