GE TMO2D User Manual Download | Manualshive

Page: 34 / 102

background image

Chapter 4. Basic Programming

26

TMO2D Digital Display User’s Manual

4.4.4 Set Backlight?

The LCD contains an electroluminescent (EL) panel to enhance the readability of the screen in dim light. EL panels
have a finite life span, and eventually dim with use. To maintain the life of the EL backlight, the display will
automatically turn the backlight off after a predetermined time period. The Backlight time-out period can be set from
(but never on) 0 to 60 minutes. The default time-out is three minutes. Example, to set the backlight time to 10 minutes:

4.4.5 Set Contrast?

The Set Contrast? submenu enables you to adjust how vividly the LCD appears in the prevailing light. To adjust the
contrast for maximum visibility:

SETUP MENU
Set Backlight?

Press [YES] to set the backlight.

SETUP MENU
Remain ON (min) [X]: 10

Use the numeric keys to enter 10. (The X’s represent the previous time entered.)

SETUP MENU
Remain ON (min) [10]:

Press [YES] to confirm the entry, and [YES] again to exit.

SETUP MENU
Set Backlight?

Press [NO] to proceed to the next submenu.

SETUP MENU
Set Contrast?

Press [YES] to set the contrast.

Adjust LCD Contrast
[INCR] decr done

Use [NO] or the right arrow key to scroll through the three selections. Press [YES] at
the INCR or DECR selections, and continue pressing [YES] until you have adjusted
the contrast to your conditions. Then select DONE and press [YES] to exit.

SETUP MENU
Set Contrast?

Press [NO] to proceed to the next submenu.

«
...
32
33
34
35
36
...
»

Summary of Contents for TMO2D







































































































Reviews:

No comments

Related manuals for TMO2D

Brand: NEC Pages: 4

Brand: NEC Pages: 3

Brand: NEC Pages: 3

Brand: NEC Pages: 37

Brand: NEC Pages: 4

Brand: Planar Pages: 24

TechTouch MO140RX

Brand: Safety 1st Pages: 10

Brand: CyberResearch Pages: 186

Brand: G-Lab Pages: 27

Brand: Feelworld Pages: 24

Brand: NEC Pages: 113

Brand: IFM Electronic Pages: 49

2407WFP - UltraSharp - 24" LCD Monitor

Brand: Dell Pages: 3

Brand: Acer Pages: 47

SyncMaster 570B TFT

Brand: Samsung Pages: 32

Brand: Samsung Pages: 38

S24H850QF series

Brand: Samsung Pages: 57

SyncMaster 570B TFT

Brand: Samsung Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands