GE TMO2D User Manual Download

Page: 56 / 102

Chapter 4. Basic Programming

TMO2D Digital Display User’s Manual

4.8.5f Set Error Handling? (cont.)

If you select any choice except

Force to Value?

, the program returns to the

Set Output Response?

entry. The

Force to

Value?

selection enables users to choose a value to which the output will go when a system error occurs from 0 to 25

mA. If you select

Force to Value?

, the program asks for two more entries.

Set Output Response
Force High?

Set Output Response
Force Low?

Set Output Response
Force to Value?

Set Output Response
Hold Last Value?

Output A, Error Value:
mA Value [X.XX]:

Use the numeric keys to enter the desired value. (The number in brackets represents
the previously entered value.) Press [YES] to enter the value, and [YES] again to
confirm the entry.

Output B, Error Value:
mA Value [X.XX]:

Use the numeric keys to enter the desired value. Press [YES] to enter the value, and
[YES] again to confirm the entry.

AUTOCAL ERROR EFFECTS
Set Output Response?

Press [NO] to proceed to the next item.

AUTOCAL ERROR EFFECTS
Done?

Press [YES] to exit the Error Effects submenu.

AUTO CALIBRATION MENU
Set Error Handling?

Press [NO] to proceed to the

Perform Auto Cal?

option.

Summary of Contents for TMO2D







































































































Search results

Summary of Contents for TMO2D

Reviews:

Related manuals for TMO2D

Brands by name

Popular brands

GE TMO2D, User Manual

Search results

Summary of Contents for TMO2D

Reviews:

Related manuals for TMO2D

Brands by name

Popular brands