GE Optima XR220amx Operator'S Manual Download Page 22

Page: 22 / 92

Chapter 2: Safety and Regulatory

Optima XR220amx X-Ray System

54400222-1EN

Rev 1 DRAFT 11092010

2-11

Operator Manual

CAUTION

Make sure that patient connected lines, tubes, etc. do not become pinched or
pulled.

Digital Detector Warnings

CAUTION

Do Not Drop.

CAUTION

Device weighs 4,536g (10.0 lbs. with battery).

CAUTION

Do not use a defibrillator while patient remains in contact with detector.

CAUTION

Maximum load is 110kg (242 lb) concentrated; 160kg (352 lb) distributed. Do not
exceed these maximum load limits.

CAUTION

Operate the detector within the temperature range of 10° C to 35° C. Store the
detector within the temperature range of 0° C to 50° C (maximum change 50° C per
hour).

Pinch Points and Crush Hazard Summary

This section lists the potential pinch points or crushing hazards that exist for the system.

Table 2-1

Pinch Points and Crush Hazard Summary

Component

Warning

System

WARNING

Potential Pinch Point:

TBD

DRAFT

REVIEW COPY

CTRL+SHIFT+F to search using Search Index (faster)

Summary of Contents for Optima XR220amx





























































































Search results

Summary of Contents for Optima XR220amx

Reviews:

Related manuals for Optima XR220amx

Brands by name

Popular brands

GE Optima XR220amx, Operator'S Manual

Search results

Summary of Contents for Optima XR220amx

Reviews:

Related manuals for Optima XR220amx

Brands by name

Popular brands