GE Optima XR220amx Operator'S Manual Download Page 57 | Manualshive

Page: 57 / 92

background image

Chapter 13: Digital Detector

Optima XR220amx X-Ray System

54400222-1EN

Rev 1 DRAFT 11092010

13-16

Operator Manual

© 2010 General Electric Company. All rights reserved.

Specifications

Detector Size and Weight

Table 13-9

Detector size and weight specifications

Environmental Contraints

This section describes the environmental conditions that the detector is designed to withstand.

CAUTION

Operation or storage outside of these constraints may cause damage to the
detector.

Table 13-10

Environmental Constraints

Item

Specification

Overall detector size

• Including handle

• Not including tether

Thickness: 27mm

Width:452mm

Height:580mm

Image Size

The active area of the x-ray panel

2024 x 2024 pixels or

40.4 x 40.4 cm

Weight

Not including the tether or grid

9.9lbs (without battery)

Battery: 0.38lbs

Item

Operating Environment Constraints

Non Operating Environment

Constraints

This column contains additional
operating environmental constraints,
within which the subsystem function
and performance capabilities shall be
in compliance.

This column defines additional Non-
operating environmental constraints,
within which the subsystem function
and performance capabilities shall be
in compliance, when returned to the
operational state, within operating
environment conditions.

DRAFT

REVIEW COPY

CTRL+SHIFT+F to search using Search Index (faster)

«
...
55
56
57
58
59
...
»

Summary of Contents for Optima XR220amx





























































































Reviews:

No comments

Related manuals for Optima XR220amx

Brand: Bartscher Pages: 22

Brand: Campbell Pages: 18

Brand: Vector Pages: 4

Brand: MacDon Pages: 84

Brand: MacDon Pages: 89

Brand: Patton electronics Pages: 18

Brand: Keithley Pages: 32

Brand: jcb Pages: 166

Brand: Yamaha Pages: 78

Brand: Fast Pages: 42

Brand: DARAY Pages: 28

Brand: Haenim Pages: 2

Tetrix 351 AC/DC Smart FW

Brand: EWM Pages: 117

Brand: FEAS Pages: 72

Brand: VBM Pages: 36

Brand: W&H Med Pages: 122

ActiveFinder One

Brand: LaserLiner Pages: 92

Brand: Yamaha Pages: 139

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands