GE MAC 600 SPY Service Manual Download Page 73

Page: 73 / 127

Revision G

MAC

600

4-23

2047426-002

Maintenance:

Check out Procedure

Check out Procedure

Operational Checks

Perform the functional checkout procedures that are applicable to the
replacement procedure that was performed.

1. Verify the power-up self-test passed. See

“Power-up Self-Test”

page 3-3

2. Verify the serial number restored successfully. See

“Serial Number

Entry”

on page 4-30

3. For units with the option enabled, verify the option enabled again

successfully (Enabled options will have in front of the options in
option activation window). See

MAC 600 Operators Manual

for

“

option entry”

details.

4. Verify that the new battery was charged successfully by checking the

battery full indicator after it has been charged for 2-3 hours
charging. See

MAC 600 Operator’s Manual.

5. Verify the time and date were set successfully. See “

Setting the date

and time”

in the

MAC 600 Operator’s Manual

Diagnostic Tests

1. Verify the System /Firmware Version was successful. See

“Testing

the System Information”

on page 3-6

for more information.

2. Verify the Display Test was successful. See

“Testing the Display”

page 3-7

for more information.

3. Verify the Buzzer Test was successful. See

“Testing the Buzzer”

page 3-8

for more information.

4. Verify the Keypad Test was successful. See

“Testing the Keypad”

page 3-9

for more information.

5. Verify the Writer Tests was successful. See

“Writer Test”

on page 3-

for more information.

6. Verify the Battery Tests was successful. See

“Battery Tests”

page 3-12

for more information.

7. Verify the Communication Tests was successful. See

“Communication Tests”

on page 3-12 for more information.

8. Verify the SD card test was successful. See

“SD Card Tests”

page 3-14

for more information.

Electrical Safety Checks

1. Leakage current tests.

2. Ground continuity test.

Summary of Contents for MAC 600 SPY
































































































































Search results

Summary of Contents for MAC 600 SPY

Reviews:

Related manuals for MAC 600 SPY

Brands by name

Popular brands

GE MAC 600 SPY, Service Manual

Search results

Summary of Contents for MAC 600 SPY

Reviews:

Related manuals for MAC 600 SPY

Brands by name

Popular brands