GE MAC 600 SPY Service Manual Download Page 27

Page: 27 / 127

Revision G

MAC

600

3-3

2047426-002

Troubleshooting:

General Fault Isolation

General Fault Isolation

Power-up Self-Test

See

Equipment Overview

in the

MAC 600 Operator’s Manual

for

information regarding the operation of the device.

On power-up, the start-up screen opens.

NOTE

Battery charging indication and time may vary.

If the equipment is not working properly:



Is the unit turned on?



Have you made changes in usage, location, or the environment that
could cause the failure?



Has the hardware or software been modified since last use?



Is operator error the cause of the problem?



Are you following the steps as described in the operator’s manual.



Is the battery installed?



If connected to the AC wall outlet, is the green external power LED
glowing?

Poor Quality ECGs

Poor quality ECGs can be caused by factors in the environment,
inadequate patient preparation, hardware failures related to the
acquisition module, lead wires, cables, or problems in the unit.

Summary of Contents for MAC 600 SPY
































































































































Search results

Summary of Contents for MAC 600 SPY

Reviews:

Related manuals for MAC 600 SPY

Brands by name

Popular brands

GE MAC 600 SPY, Service Manual

Search results

Summary of Contents for MAC 600 SPY

Reviews:

Related manuals for MAC 600 SPY

Brands by name

Popular brands