GE Druck PACE1000 Page 40 Technical Manual Download

Page: 40 / 176

4 Command and Query Summary

K0472 Revision A

4-12

INPut

The INPut subsystem shows the state of the logical inputs.

:INP:LOG

Applicability:

PACE5000, PACE6000

Command Syntax

n/a

Parameter:

Short form:
Function:
Default:

Query Syntax

:INPut[x]:LOGic?

where: x (module) = 1 or 2 (default - 1),

Short form:

:INP:LOG?

Function:

Asks for state of switch input within the controller module.

Response:

first parameter

0 = OFF, 1 = ON

second parameter

measured pressure at the time of
switching (snapshot in current pressure
units).

Description

This query returns the state of the switch input within the module and the pressure at time of
switching operations.

Example
:INP:LOG?
:INP:LOG 0, 0.8321209
Current logic OFF, pressure was 0.8321209 in current pressure units when the module was
switched to OFF condition.

Summary of Contents for Druck PACE1000

















































































































































































Search results

Summary of Contents for Druck PACE1000

Reviews:

Related manuals for Druck PACE1000

Brands by name

Popular brands

GE Druck PACE1000, Technical Manual

Search results

Summary of Contents for Druck PACE1000

Reviews:

Related manuals for Druck PACE1000

Brands by name

Popular brands