GE Druck PACE1000 Technical Manual Download Page 68

Page: 68 / 176

4 Command and Query Summary

K0472 Revision A

4-40

SENS:ALT:SLEW

Applicability:

PACE1000, PACE6000

Command Syntax

SENSE:ALTitude:SLEW

Parameter:

Short form:

SENS:ALT:SLEW

Function:

Sets the rate set-point for altitude slew.

Default: -

Query Syntax

SENSe:ALTitude:SLEW?

Short form:

SENS:ALT:SLEW?

Function:

Queries the rate set-point for altitude slew.

Response:

Decimal number representing the rate set-point for altitude slew
(rate of climb) or (vertical speed) in current units.

Description

This command sets the rate set-point for altitude slew. The query gets the rate set-point for
altitude (rate of climb) or (vertical speed) per second or minute.

Note: If the instrument is not in aero mode it returns an error: -221. Settings conflict.

Summary of Contents for Druck PACE1000

















































































































































































Search results

Summary of Contents for Druck PACE1000

Reviews:

GE Druck PACE1000, Technical Manual, Page: 68 / 176

Search results

Summary of Contents for Druck PACE1000

Reviews: