GE Druck PACE1000 Technical Manual Download Page 77

Page: 77 / 176

PACE Series SCPI Manual

K0472 Revision A

4-49

:SENS:PRES

Applicability:

PACE1000, PACE5000, PACE6000

Command Syntax

n/a

Parameter:
Short form:
Function:

Query Syntax

:SENSe[:PRESsure]?

where x = 1 or 2 is the module number (default - 1)

Short form:

:SENS?

Function:

This query reads the sensor which has been selected by the RANGE
command.

Response:

A decimal, pressure reading in the current units.

Description

Queries the pressure reading for the selected sensor in the selected units. The sensor can be
changed see, :SENSe[:PRESsure]:RANGe.
Example

TX> :SENS1:PRES?
RX> :SENS:PRES 3616.9282227
TX> :Sens2:Pres?
RX> :SENS2:PRES 3617.1921387

TX> :SENS2:PRES:RANG?
RX> :SENS2:PRES:RANG "3.50barg"
Currently module 2 sensing range is in gauge mode.
TX> :SENS2:PRES:RANG "4.50bara"
TX> :SENS2:PRES:RANG?
RX> :SENS2:PRES:RANG "4.50bara"
It has been changed to pseudo-absolute mode.

TX> :SENS2:PRES?
RX> :SENS2:PRES 4615.0807447
The reading is also changed to pseudo-absolute mode.

Note:

:SOURe[:PRESsure]:RANGe command does not change ‘SENS?’ reading.
It changes the front-panel display.

Summary of Contents for Druck PACE1000

















































































































































































Search results

Summary of Contents for Druck PACE1000

Reviews:

GE Druck PACE1000, Technical Manual, Page: 77 / 176

Search results

Summary of Contents for Druck PACE1000

Reviews: