GE Druck PACE1000 Page 92 Technical Manual Download | Manualshive

Page: 92 / 176

background image

4 Command and Query Summary

K0472 Revision A

4-64

:SENS:PRES:FILT:LPAS:BAND

Applicability:

PACE1000, PACE5000, PACE6000

Command Syntax

:SENSe[x][:PRESsure]:FILTer:[LPASs]:BAND <number>

where x = 1 or 2 is the module number (default - 1)

Parameter:

<decimal> filter band response value in % full-scale.

Short form:

:SENS:FILT:BAND

Function:

Used to set-up the response band component of the filter.

Default:

0
minimum

0

maximum

100.0

Query Syntax

:SENSe[x][:PRESsure]:FILTer:[LPASs]:BAND?

where x = 1 or 2 is the module number (default - 1)

Short form:

:SENS:FILT:BAND?

Function:

Ask for filter step response band parameter.

Response:

Number corresponding to filter step response value in % full-scale.

Description

The digital low pass filter has a response band configured as percentage of full-scale.
e.g., defaults to 0.05 %FS. If the reading has changed by more than the configured band
response value then the filtering is ignored for that conversion and the pressure goes
instantly to the new value.

Example

:SENS:PRES:FILT:LPAS:BAND
TX> :SENS:PRES:FILT:LPAS:BAND?
RX> :SENS:PRES:FILT:LPAS:BAND 50.0000000
The current setting for the filter band is 50% of full-scale, i.e., the filter applies only when the
change of pressure is within this band.

It can be changed to another number, (for example: 12% of full-scale), by sending:
TX> :SENS:PRES:FILT:LPAS:BAND 12
TX> :SENS:PRES:FILT:LPAS:BAND?
RX> :SENS:PRES:FILT:LPAS:BAND 12.0000000

«
...
90
91
92
93
94
...
»

Summary of Contents for Druck PACE1000

















































































































































































Reviews:

No comments

Related manuals for Druck PACE1000

Brand: Labnet Pages: 5

Brand: Yardistry Pages: 9

Brand: Modulate Pages: 2

Brand: B-K lighting Pages: 3

Brand: Ecler Pages: 108

Brand: R&S Pages: 121

Brand: Farmet Pages: 102

Brand: G-Systems Pages: 60

Brand: G-Lab Pages: 16

Brand: G&G Pages: 2

Brand: EuroLite Pages: 28

Brand: Quick Pages: 24

Brand: JDS Uniphase Pages: 144

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 14

ST70 Instrument

Brand: Raymarine Pages: 12

Brand: Raven Pages: 73

Brand: Tascam Pages: 3

Brand: RAB Lighting Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands