GE Druck PACE1000 Technical Manual Download Page 148

Page: 148 / 176

4 Command and Query Summary

K0472 Revision A

4-120

:SYST:AREA

Applicability:

PACE1000, PACE5000, PACE6000

Command Syntax

:SYSTem:AREA

Parameter:

String

Short form:

SYST:AREA

Function:

Sets a group of parameters for an area of the world.

Query Syntax

:SYSTem:AREA?

Short form:

:SYST:AREA?

Function:

Queries area setting.

Response: Sends:

EUROPE, or EUR
USA
JAPAN or JAP
ASIA
ROW (rest of the world)

Description

This command instructs the instrument to enable a group of default settings for an area of
the world.

:SYST:AREA
TX> :SYST:AREA?
RX> :SYST:AREA EUR
The current area of use is set to Europe.

Can be set to another area, such as Japan:
TX> :SYST:AREA jap
TX> :SYST:AREA?
RX> :SYST:AREA JAP

Set to the rest of the world:
TX> :SYST:AREA row
TX> :SYST:AREA?
RX> :SYST:AREA ROW

Summary of Contents for Druck PACE1000

















































































































































































Search results

Summary of Contents for Druck PACE1000

Reviews:

GE Druck PACE1000, Technical Manual, Page: 148 / 176

Search results

Summary of Contents for Druck PACE1000

Reviews: