GE AKTA pilot 600 User Manual Download Page 89

Page: 89 / 140

Maintenance

About this chapter

Regular maintenance of the ÄKTA pilot 600 system is essential for reliable function.

This chapter describes the recommended maintenance schedules and provides detailed
instructions for maintenance operations.

In this chapter

This chapter contains the following sections:

See page

Section

5.1 Maintenance manager

5.2 Maintenance schedule

5.3 Cleaning procedures

100

5.4 Calibration procedures

109

5.5 Replacement procedures

Maintenance tasks

Refer to the ÄKTA pilot 600 Operating Instructions for instructions concerning the following
maintenance tasks:

•

Cleaning the instrument

•

Cleaning the flow path

•

Cleaning and storing the pH electrode

•

Changing the pump rinsing solution

•

Replacing the pump rinsing tubing

•

Replacing flow path tubing and connectors

•

Replacing valve membranes

•

Replacing the main fuses

ÄKTA pilot 600 User Manual 29274559 AA

5 Maintenance

Summary of Contents for AKTA pilot 600













































































































































Search results

Summary of Contents for AKTA pilot 600

Reviews:

Brands by name

Popular brands

GE AKTA pilot 600, User Manual

Search results

Summary of Contents for AKTA pilot 600

Reviews:

Brands by name

Popular brands