[7]
Run in Range/No Warn-
ing
Motor runs within programmed current ranges, see parameters 4-50 and 4-51. No warnings are present.
[8]
Run on ref/No Warning
Motor runs at reference speed.
[9]
Alarm
An alarm activates output.
[10]
Alarm on Warning
An alarm or warning activates output.
[12]
Out of Current Range
Motor current is outside range set in parameters 4-50 and 4-51.
[13]
Below Current, low
Motor current is lower than set in par. 4-50.
[14]
Above Current, high
Motor current is higher than set in par. 4-51.
[21]
Thermal Warning
Thermal warning is present when temperature exceeds limit in motor, frequency converter, brake resistor or thermistor.
[22]
Ready, No Thermal
Warning
Frequency converter is ready for operation and no over-temperature warning is present.
[23]
Remote Ready, No Ther-
mal Warning
Frequency converter is ready for operation in Auto mode, and no over-temperature warning is present.
[24]
Ready, Voltage OK
Frequency converter is ready for operation and mains voltage is within specified voltage range.
[25]
Reverse
Motor runs/is ready to run clockwise when logic = 0 and counter clockwise when logic = 1. Output changes as soon
as reversing signal is applied.
[26]
Bus OK
Active communication (no time-out) via serial communication port.
[28]
Brake, No Warn
Brake is active, and no warnings are present.
[29]
Brake Ready/No Fault
Brake is ready for operation, and no faults are present.
[30]
Brake Fault (IGBT)
Protects frequency converter if fault on brake modules is present. Use relay to cut out main voltage from frequency
converter.
[32]
Mech. Brake Control
Enables control of external mechanical brake, see parameter group 2-2*.
[36]
Control Word Bit 11
Bit 11 in control word controls relay.
[51]
Local Ref Active
[52]
Remote Ref Active
[53]
No Alarm
[54]
Start Cmd Active
[55]
Running Reverse
[56]
Drive in Hand Mode
[57]
Drive in Auto Mode
[60]
Comparator 0
See par. group 13-1*. If comparator 0 is evaluated as TRUE, output goes high. Otherwise, it is low.
[61]
Comparator 1
See par. group 13-1*. If comparator 1 is evaluated as TRUE, output goes high. Otherwise, it is low.
[62]
Comparator 2
See par. group 13-1*. If comparator 2 is evaluated as TRUE, output goes high. Otherwise, it is low.
[63]
Comparator 3
See par. group 13-1*. If comparator 3 is evaluated as TRUE, output goes high. Otherwise, it is low.
[70]
Logic Rule 0
See par. 13-4*. If Logic Rule 1 is evaluated as TRUE, output goes high. Otherwise, it is low.
[71]
Logic Rule 1
See par. 13-4*. If Logic Rule 2 is evaluated as TRUE, output goes high. Otherwise, it is low.
[72]
Logic Rule 2
See par. 13-4*. If Logic Rule 3 is evaluated as TRUE, output goes high. Otherwise, it is low.
[73]
Logic Rule 3
See par. 13-4*. If Logic Rule 3 is evaluated as TRUE, output goes high. Otherwise, it is low.
[81]
Logic Controller Digital
Output B
See par. 13-52
SL Control Action
. When Logic Controller Action
Set dig. out. A high
[39] is executed, input goes high.
When Smart Logic Action
Set dig. out. A low
[33] is executed, input goes low.
5-40 Function Relay
Option:
Function:
[0]
*
No Operation
Select function from available relay output range.
4.6.4. 5-5* Pulse Input
Set par. 5-15 to choice [32] pulse input. Now terminal 33 handles a pulse input in the range from Low frequency, par. 5-55, to High frequency, par. 5-56. Scale
frequency input via par. 5-57 and par. 5-58.
AF-60 LP™ Micro Drive Programming Guide
34
4
