GBC A1, Operation & Instruction Manual

Page: 7 / 110

Multi Function Professional Puncher
C. Paper Clearing:
When paper is jammed in the paper path of
Professional Puncher the LCD display shows the
area where a sheet(s) is jammed.
Area Description
Area A
If paper is jammed in the Punch
handle until it latches with the locking mechanism.
Reach and remove the jammed paper.
To close the paper guide, press the upper latch
lever while holding the guide plate handle and
lower the guide plate to close it firmly.
Area B1
If paper is jammed in the downward paper
move the chute to the right, reach in and remove
the jammed paper.
Ensure the paper chute is closed.
Area B2
If paper is jammed in the right bottom chute, press
the top lever while holding the bottom lever. This
will unlatch the chute; continue to open the chute
until it reached the magnet on the right side. Reach
in and remove the paper. To return the chute to t
closed position, move it back in the opposite
direction until the latch mechanism is activated.
Ensure the paper chute is closed.
Area B3
If paper is jammed in the left
unlatch the chute, reach in and remove any
jammed paper.
Ensure the paper chute is closed.
Area B4
If paper is jammed in the upward paper chute,
move the door to the left, reach in and remove the
jammed paper.
Ensure the paper chute is closed.
Area B2/B3
Before uninstalling the die set, ensure Area
and B3 are cleared of any jammed paper. If there
is jammed paper cannot be removed from
B2 and B3, uninstall the die set to remove the
jammed paper. (see Section
Interchangable die sets)
Multi Function Professional Puncher
When paper is jammed in the paper path of
the LCD display shows the
where a sheet(s) is jammed.
Description
If paper is jammed in the Punch Bypass, lift the
handle until it latches with the locking mechanism.
each and remove the jammed paper.
press the upper latch
while holding the guide plate handle and
lower the guide plate to close it firmly.
If paper is jammed in the downward paper chute,
t, reach in and remove
Ensure the paper chute is closed.
If paper is jammed in the right bottom chute, press
the top lever while holding the bottom lever. This
will unlatch the chute; continue to open the chute
until it reached the magnet on the right side. Reach
in and remove the paper. To return the chute to the
closed position, move it back in the opposite
he latch mechanism is activated.
Ensure the paper chute is closed.
left bottom chute,
unlatch the chute, reach in and remove any
the paper chute is closed.
If paper is jammed in the upward paper chute,
t, reach in and remove the
Ensure the paper chute is closed.
Before uninstalling the die set, ensure Area B2
are cleared of any jammed paper. If there
jammed paper cannot be removed from Area
nstall the die set to remove the
jammed paper. (see Section 4. Changing the
5. USER DISPLAY
Located on the front of the Professi
LCD panel that provides Messages; Settings and I
the functions of the punch unit.
LCD Panel Overview
Messages on the LCD Panel
1. Ready Bypass
Professional Puncher is ready to bypass, sheets will
punched.
2. Ready to Punch
Professional Puncher is ready to process a punch job, all sheets
through the unit will be punched.
3. Ready to Crease
Professional Puncher is ready to process a crease job. For some
controllers, all sheets through the u
4. Running Bypass
This is displayed when Bypass mode
5. Running Punch
This is displayed when Punch mode is in operation.
6. Running Crease
This is displayed when Crease mode is in operation.
7. Chip Tray Full
When the punch container becomes full of waste paper chips, this
message will be displayed.
8. Chip Tray Out
When the punch container is removed or not fully inserted into the
punch unit, this message will be displayed
9. Check Die
When the Die Set is removed or
unit, this message will be displayed.
displayed the punch unit will run in Bypass mode only
10. Close Door
When the Front door is open or not completely closed this
message will be displayed.
11. Paper Jam
When a sheet of paper becomes jammed within the punch unit,
this message is displayed. See
PAPER CLEARING for instructions on how to remove a
sheet.
7
EN
Multi Function Professional Puncher – A1
Professional Puncher is a user interactive
Messages; Settings and Information relating to
CD Panel Overview
is ready to bypass, sheets will not be
is ready to process a punch job, all sheets
through the unit will be punched.
Professional Puncher is ready to process a crease job. For some
controllers, all sheets through the unit will be creased.
This is displayed when Bypass mode is in operation.
Punch mode is in operation.
This is displayed when Crease mode is in operation.
punch container becomes full of waste paper chips, this
When the punch container is removed or not fully inserted into the
be displayed.
When the Die Set is removed or not fully inserted into the punch
displayed. When this message is
displayed the punch unit will run in Bypass mode only.
When the Front door is open or not completely closed this
When a sheet of paper becomes jammed within the punch unit,
this message is displayed. See the section of this manual titled
for instructions on how to remove a jammed