manualshive.com logo in svg

Gateway 6-Bay mBTX PRO, User Manual

Share
Download
Gateway 6-Bay mBTX PRO User Manual Download Page 141

www.gateway.com

133

Replacing the power supply

To replace the power supply:

 

1

Remove the side panel by following the instructions in 

“Removing the side panel” on 

page 121

.

2

For more stability, place your computer on its side. To avoid scratching the case, place it 
on a towel or other non-abrasive surface.

3

Disconnect the power supply cables from all components (such as hard drives, CD or DVD 
drives, and the system board), noting their locations and orientation. (You will reconnect 
the cables after you install the new power supply.)

4

Remove the three screws that secure the power supply to the computer.

5

Slide the power supply away from the back of the computer, then pull it down and remove 
it.

6

Install the new power supply into the case, then install the three screws to secure the power 
supply to the case.

7

Reconnect the power supply cables using your notes from 

Step 3

.

8

Replace the side panel by following the instructions in 

“Replacing the side panel” on 

page 123

.

Tip

You need a Phillips screwdriver to replace the power supply.

Screws

Summary of Contents for 6-Bay mBTX PRO























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands