manualshive.com logo in svg

Gateway 6-Bay mBTX PRO, User Manual

Share
Download
Gateway 6-Bay mBTX PRO User Manual Download Page 134

CHAPTER 13: Adding and Replacing Components

126

Replacing the system battery

If the computer clock does not keep time or the settings in the BIOS Setup utility are not saved 
when you turn off your computer, replace the system battery. Use a battery of the same size 
and voltage as the original battery that was in your computer.

To replace the battery:

 

1

Restart your computer.

2

During the restart, press and hold the 

F1

 key. The main menu of the BIOS Setup utility 

opens.

3

Write down all the values in the menus and submenus, then exit from the utility.

4

Shut down your computer.

5

Remove the side panel by following the instructions in 

“Removing the side panel” on 

page 121

.

6

For more stability, place your computer on its side. To avoid scratching the case, place it 
on a towel or other non-abrasive surface.

7

Locate the old battery on the system board and note its orientation. You will need to install 
the new battery the same way.

8

Push the battery release tab. The battery pops out of the socket.

9

Make sure that the positive (+) side of the new battery is facing up, then press the battery 
into the socket until it snaps into place.

10

Replace the side panel by following the instructions in 

“Replacing the side panel” on 

page 123

.

11

Reconnect all external cables and the power cord.

12

Turn on your computer.

13

Open the BIOS Setup utility.

14

In the BIOS Setup utility, restore any settings that you wrote down in 

Step 3

.

15

Save all your settings and exit the BIOS Setup utility.

Warning

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer. 

Dispose of used batteries following the manufacturer’s instructions.

Battery release tab

Summary of Contents for 6-Bay mBTX PRO























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands