Gap Diagnostic IIDTool Pro G3 User Manual Download Page 36

Page: 36 / 188

IIDT

ool

User Manual G3 units: Version 37, Firmware V4.0

2.2 Create a user account

Purpose

Before first usage of the IIDTool, it is strongly recommended to update the tool. But first, the user must

perform its free registration. To access the advanced programming features, it will be required to pro

ceed with the activation process to obtain a licence for personal use.

A user account can be created in the mobile App or on the GAP Diagnostic website

Note :

If the IIDTool was purchased on the GAP diagnostic website, it is not required to create a new

user account.

Principle

Create your individual profile in the mobile App OR on the manufacturer’s website; a proprietary link

will be established between the tool and its user.

Note :

Registering, followed by updating and activation of the tool gives the user:

•

Exclusive access to advanced programming functions and data backup

•

Faster access when connected to the vehicle

2.2.1 Create a user account on the mobile device (preferred method)

1- Start the App

2- Click on Login, top right

3- Click on Register and fill up the fields

Figure 13.

Summary of Contents for IIDTool Pro G3


























































































































































































Search results

Summary of Contents for IIDTool Pro G3

Reviews:

Brands by name

Popular brands

Gap Diagnostic IIDTool Pro G3, User Manual

Search results

Summary of Contents for IIDTool Pro G3

Reviews:

Brands by name

Popular brands