manualshive.com logo in svg

Fujitsu Siemens Computers CentricStor V3.1D, User Manual

Get your hands on the user manual for the Fujitsu Siemens Computers CentricStor V3.1D. This essential manual can be downloaded for free from our website, providing you with all the information you need to optimize your experience with this top-of-the-line product.

Share
Download
background image

486

  

 U41117-J-Z125-7-76

Message lines

Explanation of console messages

SXRD001 

NOTICE: raidd: 0:0:1 - disk state changed (Dead -> Write-Only)

Meaning

A rebuild is active for the physical disk of controller 0, channel 0, target ID 1.

SXRD001 

NOTICE: raidd: 0:0:1 - disk state changed (Dead -> Online)

Meaning

A rebuild was successful for the physical disk of controller 0, channel 0, target ID 1. All the 
associated logical disks are fully operational (redundant) again.

SXRD001 

ALERT: raidd: c50d0 - state changed (Online -> Critical)

Meaning

The logical disk 0 on controller 0 no longer provides any redundancy. This indicates a 
hardware problem with a physical disk belonging to the addressed logical disk.

Response

Notify maintenance staff.

SXRD001 

ALERT: raidd: c50d0 - state changed (Critical -> Offline)

Meaning

A further physical disk belonging to the logical disk 0 on controller 0 has failed. The 
addressed logical disk is no longer accessible.

Response

Notify maintenance staff.

SXRD001 

NOTICE: raidd: c50d0 - state changed (Critical -> Online)

Meaning

The logical disk 0 on controller 0 has completed a rebuild and once again provides redun-
dancy.

Messages during the start phase

SXRD001 

ALERT: raidd: 0:0:3 - disk state is Dead

Meaning

This message is only generated when the raidd is started at system boot. The physical disk 
on controller 0, bus 0, target 3 was failed as the system booted. This indicates a hardware 
problem with the addressed physical disk.

Response

Notify maintenance staff.

SXRD001 

ALERT: raidd: 0:0:3 - disk state is Write-Only

Meaning

This message is only generated when the raidd is started at system boot. As the system 
was started a rebuild was active for the physical disk on controller 0, bus 0, target 3.

Summary of Contents for CentricStor V3.1D

































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CentricStor V3.1D

Symantec 20032623 - Endpoint Protection Small Business Edition Implementation Manual preview
20032623 - Endpoint Protection Small Business Edition
Brand: Symantec Pages: 351
Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1 Installation Manual preview
NETWORK AND SECURITY MANAGER 2010.4 - REV1
Brand: Juniper Pages: 244
Valgrind BBV Quick Start Manual preview
BBV
Brand: Valgrind Pages: 319
Samsung SyncMaster S23A950D User Manual preview
SyncMaster S23A950D
Brand: Samsung Pages: 90
Samsung SyncMaster T23A750 E-Manual preview
SyncMaster T23A750
Brand: Samsung Pages: 292
Billion BiGuard C01 Quick Installation Manual preview
BiGuard C01
Brand: Billion Pages: 18
Yamaha DM2000 V2.1 Supplementary Manual preview
DM2000 V2.1
Brand: Yamaha Pages: 4
Yamaha ASIO DirectKS Owner'S Manual preview
ASIO DirectKS
Brand: Yamaha Pages: 6
Yamaha Audio Owner'S Manual preview
Audio
Brand: Yamaha Pages: 7
Yamaha Arp Owner'S Manual preview
Arp
Brand: Yamaha Pages: 9
Yamaha AE041 Owner'S Manual preview
AE041
Brand: Yamaha Pages: 11
Yamaha Card Filer Manual preview
Card Filer
Brand: Yamaha Pages: 15
Yamaha Add-On Effects Manual preview
Add-On Effects
Brand: Yamaha Pages: 14
Yamaha AN200 Editor Manual preview
AN200 Editor
Brand: Yamaha Pages: 72
Yamaha 03DVEK Owner'S Manual preview
03DVEK
Brand: Yamaha Pages: 129
VDO TIS-COMPACT III Brochure preview
TIS-COMPACT III
Brand: VDO Pages: 8
Ulead GIF ANIMATOR 4.0 User Manual preview
GIF ANIMATOR 4.0
Brand: Ulead Pages: 64
Red Hat ENTERPRISE LINUX 3 - SECURITY GUIDE Manual preview
ENTERPRISE LINUX 3 - SECURITY GUIDE
Brand: Red Hat Pages: 410

Brands by name

Popular brands

Load more brands