Fujian Xingyi Polishing Machine 800-4E Manual Download | Manualshive

Page: 18 / 65

background image

Fujian Xingyi Polishing Machine

Co.,Ltd

Manual Of Remote Control Floor Grinder 800-4E

Factory Addresss:NO.C2 ,Area 11 ,AnPing Development Area, Quanzhou ,Fujian province ,China

Postal Code:362200

Tel: +86-595-36792992

Mob: +86-15960788816

Use only Xingyi parts and accessories, For your own safety, The Safety of others and the life of your

machines.

18

down.

3. Machine sure the plug is in resetting position then start the machine.

3.3.6 The angle adjustment of swing lever.

Hold the stainless steel arm with one hand, and pull the swing lever handle

with another hand, then the height and position of the full machine control

panel can be adjusted.

Note:

Make sure the swing lever is fully located on the base plate after your adjusting

and then use the machine.

3.4 Front wheel

3.4.1 The dismantle of front wheel

The installation of supporting wheel can make the turning of machine

more smooth, and save labor in transportation.

Dismantle or overturn the support wheel when grinding.
How to dismantle: Press the emergency stop switch, plug off the machine,

take out the R plug from the open pin, and you can remove the front wheel.

Installation of front wheel : Press the emergency stop switch, plug off the

machine, align the front wheel to the holes on the frame beside the motor, and
fix with the pin, finally lock with the R pin.

«
...
16
17
18
19
20
...
»

Summary of Contents for 800-4E


































































Reviews:

No comments

Related manuals for 800-4E

Brand: Fellowes Pages: 7

Brand: Singer Pages: 29

swingo 755B power

Brand: Taski Pages: 12

Brand: Baby Lock Pages: 198

Brand: Singer Pages: 12

Brand: JUKI Pages: 75

Brand: KLINDEX Pages: 32

Brand: Duerkopp Adler Pages: 38

Easy Step Plus MS 80

Brand: Impex Pages: 9

imagePRESS C7010VPS/C6010VPS/C6010S Series

Brand: Canon Pages: 100

Dream 20 Stitch

Brand: usha Pages: 38

Brand: Singer Pages: 15

Brand: Singer Pages: 13

Brand: Singer Pages: 15

Brand: Singer Pages: 14

Brand: Singer Pages: 21

Brand: Singer Pages: 42

Brand: Singer Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands