Fritsch PULVERISETTE 5 Operating Instructions Manual Download Page 49

Page: 49 / 72

17.

Re-tighten the screws in the additional clamping system with a hex

key.

DANGER!
The additional clamping system may be loosened

due to the clamping of the Safe-Lock using the

clamping lever. Check the screw connections of

the additional clamping system and the Safe-Lock

tensioning device for tight fit before starting

grinding. Failure to observe this instruction may

lead to serious material damage or personal

injury.

DANGER!
After several minutes of grinding and in the cooling-

down phases, check that the tensioning device is firmly

connected.

If the Safe‐Lock system is correctly tensioned, the

clamping lever is automatically pulled downwards by

the eccentric when horizontal.

7.2 Grinding in inert gas with gassing lid

NOTICE!
Observe imbalance offsetting! (See

Chapter 6.6

„Mass balance“ on page 39).

NOTICE!
Before every grinding operation, check the valves of the

gassing lid ensuring that they are clean and properly

secured. See chapter

Chapter 7.2.4 „Cleaning the

valves“ on page 52.

Accessories

- 49 -

Summary of Contents for PULVERISETTE 5









































































Search results

Summary of Contents for PULVERISETTE 5

Reviews:

Related manuals for PULVERISETTE 5

Brands by name

Popular brands

Fritsch PULVERISETTE 5, Operating Instructions Manual

Search results

Summary of Contents for PULVERISETTE 5

Reviews:

Related manuals for PULVERISETTE 5

Brands by name

Popular brands