Fritsch PULVERISETTE 5 Operating Instructions Manual Download Page 24

Page: 24 / 72

4.6 Settings in setup mode

4.6.1 Setting the imbalance check

CAUTION!
The imbalance check can be disabled at your own risk.

Fritsch assumes no liability for damage resulting from

the deactivation of the imbalance check!

NOTICE!
The highest level of sensitivity is set for the imbalance

check as the factory default. In order to adjust the

imbalance check to suit your applications as best as

possible, set the value for the imbalance check as

explained in Chapter

Chapter 4.6.1 „Setting the

imbalance check“ on page 24. Please note that you

have to redefine this setting for various parameters

with different grinding sets and balls.

Activation / deactivation of the imbalance check in setup mode:
1.

Press and hold the STOP button on the front of the control panel.

Switch on the device with the main switch (10) on the back of the

device. There is a brief display check. After roughly 3 seconds

setup mode is started and the STOP button can be released.

If POWER SUPPLY is flashing, the device is in setup mode. If

POWER SUPPLY is not flashing, repeat the procedure.

Installation

- 24 -

Summary of Contents for PULVERISETTE 5









































































Search results

Summary of Contents for PULVERISETTE 5

Reviews:

Related manuals for PULVERISETTE 5

Brands by name

Popular brands

Fritsch PULVERISETTE 5, Operating Instructions Manual

Search results

Summary of Contents for PULVERISETTE 5

Reviews:

Related manuals for PULVERISETTE 5

Brands by name

Popular brands