manualshive.com logo in svg

Fritsch PULVERISETTE 5, Operating Instructions Manual

Share
Download
Fritsch PULVERISETTE 5 Operating Instructions Manual Download Page 20

4 

Installation

4.1  Transport

The device is delivered on a transport pallet with a wooden cover. We

recommend using a forklift or pallet truck for transporting the packed

device.

DANGER!
Do not step under the transport pallet during transport.

WARNING!
Improper lifting can lead to personal injury or property

damage. The machine is only to be lifted with suitable

equipment and by qualified personnel.

The guarantee excludes all claims for damage due to improper transport.

4.2  Unpacking

n

Pull out the nails that fasten the lid to the surrounding packaging.

n

Remove the lid.

n

Take out the accessories.

n

Pull out the nails that fasten the surrounding packaging to the trans-

port pallet.

n

Then lift the wooden surround over and away from the device.

n

The pre-perforated segments can be detached so that the foam parts

can be removed more easily.

n

Please store the transport packaging so that it can be reused if you

need to return the product. Fritsch GmbH accepts no liability for

damage caused by improper packaging (packaging that is not from

Fritsch).

n

Compare the contents of the delivery with your order.

 

Installation

 

 

- 20 -

 

Summary of Contents for PULVERISETTE 5









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands