manualshive.com logo in svg

Fritsch PULVERISETTE 5, Operating Instructions Manual

Share
Download
Fritsch PULVERISETTE 5 Operating Instructions Manual Download Page 21

Grinding bowls made of tempered steel may have

recesses on the surface caused during production. They

do not have an impact on grinding or the grinding

results and usually disappear after the first grinding

operation.
These recesses on the surface, if present, are within the

range of the permissible production tolerances. Com‐

plaints relating to such grinding bowls therefore cannot

be accepted.

4.3  Setting up

DANGER!
Do not step under the transport pallet during transport.

CAUTION!
The weight of the planetary mill is approx. 120kg!

NOTICE!
Never operate the mill while it is standing on the trans-

port pallet!

NOTICE!
Keep any obstructions away from the air outlet on the

side ventilation grate. Risk of overheating!

n

Lift the mill from the transport pallet.

n

6 screws connect the mill to the transport pallet. Remove the screws.

n

Place the mill with the transport pallet back down.

n

Lift the mill off the transport pallet.

n

Place the mill on a flat, stable surface. It is not necessary to fasten it

in place.
The mill can be placed on a stable table.

n

Make sure that the mill is easily accessible. There has to be sufficient

space to reach the main switch on the back side of the device.

 

Installation

 

 

- 21 -

 

Summary of Contents for PULVERISETTE 5









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands