manualshive.com logo in svg

Fritsch PULVERISETTE 5, Operating Instructions Manual

Share
Download
Fritsch PULVERISETTE 5 Operating Instructions Manual Download Page 45

7 

Accessories

7.1  Additional clamping system for grinding harmful substances or in a gas atmosphere.

The additional clamping system is used to transport a grinding bowl filled

with inert gas or harmful substances from a glove box to the planetary

mill and back again. This ensures that no harmful substances can be

inhaled.
There are two ways of gassing the grinding bowls:
1.

Grinding bowls with standard lids have to be filled in a glove box

with an inert gas atmosphere and closed using the additional

clamping system. Using this procedure you can even grind haz-

ardous substances!

2.

Grinding bowls with gassing lids can also be closed and gassed out-

side the device using the additional clamping system.

7.1.1  Locking the additional clamping system into place

1.

Use the black Viton sealring instead the white Teflon sealring to

seal the grinding bowl if you use the additional clamping system.

2.

Place the grinding bowl in the grinding bowl adapter (a) of the

additional clamping system.

 

Accessories

 

 

- 45 -

 

Summary of Contents for PULVERISETTE 5









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands