Franke La Marzocco FB-70 Training Manual Download Page 40

Page: 40 / 67

9. Using a 22 mm

wrench, loosen the

valve stem from the

valve body.

10. Remove the valve

stem and plunger.

11. Inspect the

plunger for a dam-

aged or worn seal.

Inspect the valve

stem and seat for

scale build-up.

Replace as nec-

12. Reinstall the valve

plunger and stem.

Reinstall the stem to

the valve body.

13. Reinstall the valve

coil and retaining nut.

Reinstall the valve

stem cap.

14. Using a 14 mm

wrench, tighten the cap

to the stem.

15. Reinstall the valve.

16. Tighten both fit

tings.

17. Reattach the power leads to the coil.

18. Replace the control board bracket.

19. Replace the machine’s surround and right side panel.

20. Replace the machine’s top panel.

Summary of Contents for La Marzocco FB-70




































































Search results

Summary of Contents for La Marzocco FB-70

Reviews:

Related manuals for La Marzocco FB-70

Brands by name

Popular brands

Franke La Marzocco FB-70, Training Manual

Search results

Summary of Contents for La Marzocco FB-70

Reviews:

Related manuals for La Marzocco FB-70

Brands by name

Popular brands