Franke La Marzocco FB-70 Training Manual Download Page 7

Page: 7 / 67

12. Hot Water Nozzle

The hot water nozzle is installed on the outlet of the hot water valve. When the valve is

energized, hot water from the steam boiler is forced, by steam pressure, through the valve

and out of the nozzle.

13. Sight Glass

The sight glass indicates the amount of water in the steam boiler only,as the coffee boiler is

always fully saturated with water. The sight glass should read between 2/3 and 3/4 during

normal operation.

14. Steam Wand

The steam allows the barista to prepare milk for drinks suchs as lattes, cappuccinnos, and

mochas. The La Marzocco uses stainless steel wands that rotate 360 degrees.

Body Panels

For most repairs, it may be necessary to remove a body panel.

1. Top Trim

2. Upper Surround Panel

3. Left Side Panel

4. Right Side Panel

5. Front Panel

6. Cup Tray

7. Cup Tray Grates

8. Group Cover

9. Drip Tray & Grates

Steaming

Body

O-ring

Glass

Fiber Gasket

Securing Bezel

Fitting

Bleed Screw

Washer

Summary of Contents for La Marzocco FB-70




































































Search results

Summary of Contents for La Marzocco FB-70

Reviews:

Brands by name

Popular brands

Franke La Marzocco FB-70, Training Manual

Search results

Summary of Contents for La Marzocco FB-70

Reviews:

Brands by name

Popular brands